TV Audio Mount 2.1Television Wall Mount with Integrated 2.1 Sound System
11STEP 4Place the cardboard template on the wall where you want to mount the system. Is using a non-solid wall,, such as concrete, use a stud fi nder t
12STEP 5A ach the Wall Plate to the wall.Wood Stud MountingThe Wall Plate must be mounted, at the top and bo om, to at least 2 wooden studs, spaced
13NOTE: Be sure to choose a wall area that is strong enough to support the combined weight of the TV and Audio Mount. The loca on should be safe from
14STEP 6A ach the TV to the TV Bracket Connec on (Figure 8). First, remove the round tube (B) from the TV Bracket Connec on. Next, choose the corre
15NOTE: You will need at least 2 people to fi nish this moun ng procedure. To avoid possible injury, do not a empt to mount the TV alone.NO!YES!STEP
16STEP 8Adjust the two side speakers to the correct width (Figure 10).Near the top on each side of the TV Audio Mount you will see a locking screw tha
17STEP 9Hang the pre-assembled TV unit on the pole and clip the screws (A) into the lower channel of the Wall Plate and ghten on both sides when the
18STEP 10Connect the audio wires. Your TV Audio Mount has three ways to input the audio from your TV (see Figure 12).1. Line Level Out is located on
19STEP 11Adjust the angle of the TV and then ghten the handles (D) and locking screws (A) (Figure 13). You can then adjust the width and angle of th
20TV SettingsFor your TV Audio Mount to work properly, you must adjust your TV se ngs for op mal output to the Audio Mount.1. Make sure your TV Ba
3TABLE OF CONTENTSSafety Instructions ...
21Turn the TV Audio Mount System ON/OFFLINESelect the source to Line InOPTSelect the audio source to Op calSelect hearing impaired or standard modeMU
22Programming a Learning Remote If you have a universal (learning) remote, it should be capable of learning the TV Audio Mount remote control codes. F
23LED IndicatorsThe LED indicator is located on the right side speaker in the logo plate. It is used to help you monitor and control your audio syste
24Audio SettingsThe Audio Mount Remote Control does not func on in a press and hold mode. You must depress the bu on mul ple mes to increase or
25Model Number Description Product ImageTVAMDVDSHELF Add-on DVD Shelf for Audio MountTVAMPEDESTAL Pedestal MountFMWM3260-TVAM Full Mo on Wall Mount
26Model Number Description Product ImageCM3260-TVAM Ceiling MountFTVS3260-TVAM Rolling Floor StandACCESSORIES
27Cleaning the Housing and Remote Control• Do not use vola le solvents such as toluene, rosin or alcohol to clean the TV Audio Mount. These chemical
28If the TV Audio Mount System fails to operate, check the opera on in accordance with the following.Problem SolutionNo power Check to verify that th
29Cable ComplianceCau on: Always use a power cable that is properly grounded. Please use the AC Cords listed below for each area:USA ULCanada CSA
30Features• Klippel laser-op mized 6.5” woofer for high linear excursion and powerful bass• 24 bit/48 kHz Digital EQ and Crossovers for high qualit
4Please read this en re manual carefully before moun ng the system to avoid bodily injury and/or any property loss. If you do not understand these d
31This 12 month limited warranty is provided by Metra Electronics Corpora on for the Metra product iden fi ed by the purchaser’s registra on as indi
©2011 Metra Electronics Corpora on, 460 Walker Street, Holly Hill, FL 32117-2699Specifi ca ons are subject to change without no ce. All trademarks a
5• WARNING: To reduce the risk of fi re or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dri
6IntroductionCongratula ons on the purchase of your new Audio Solu ons 2.1 TV Audio Mount System. For maximum benefi t, please read the en re manual
7Wall Plate Mounting Hardware# Part Image DescripƟ on Qty1 Square Head Screw62Concrete Bolt 63M8 Washer 6TV Bracket Assembly Hardware# Part Image Desc
8STEP 1Read and understand all of the enclosed instruc ons and verify that all parts are present and appear in good working order before you begin.ST
9Figure 2 - TV Bracket ConnectionFigure 3 - Sound System Wall PlateINSTALLATION
10STEP 3Remove the two handles (D) (Figure 4). Rotate the pole assembly downward to gain clear access to the top moun ng holes. Figure 4 - Remove Han
Kommentare zu diesen Handbüchern